Filkret 300 is a cement based surface repairing and sealing mixture, monocomponent, polymerizable, having high stability. The product conforms to the requirements of the 039-2000 (TS 11140-1993) standard: “Adhesives – cement based (hydraulic conjunction), suitable for glazed, ceramic, and floor tiles”.

This repair mixture can be applied in the following areas:

• preparation of even surfaces before painting dry concrete surfaces;
• correction of irregularities existing in concrete surfaces during plastering and repair operations on of walls and ceilings;

• the product is mixed with water only, easy applicable;
• excellent thickness;
• provides correct preparation of surfaces;
• easily accepts the dye due to white color;
• provides high adhesive ability to concrete and plastered surfaces;
• easily applicable on large surfaces;
• does not form cracks;

Preparation of the surfaces. Cement based building surfaces to be repaired should be rigid, clean and dust-free, they should be totally free of any fat, rust, and paraffin residues deteriorating adhesive force. The surface should be cleaned from metal and wooden particles. Provide water saturation of the surface to be treated with the mixture, however there should not be free water remained on the surface.

Preparation of the mixture. Pour appropriate  amount of water measured with a measuring device to clean container, and gradually add the Filkret 300 repair mixture. Prepare this mixture for 4 minutes using 400-600 RPM mixer till the mixture is entirely homogeneous. Mix again in approximately 4 minutes during 30-minute period, bringing the product to conditions ready for application.

Application. Spread the prepared mixture over the surface to form 1 – 5mm thick layer with the help of a trowel. Let the mixture dry, and splash water on the surface of the mixture using plaster brush. Then correct the surface in required manner using steel or wooden trowel. In case of applying the Filkret 300 product in the open area on large open surfaces, especially in warm, dry and windy weather conditions, prevent evaporation of the solution during 24-48 hours using soaked cloth, duck fabric, or any other active solution.

Recommendations. The Filkret 300 repair mixture should not be used under epoxide based paints. The mixture prepared for repair works should be used within 30 minutes at +200C temperature. For +320C temperature this period is reduced to 20 minutes. In case of the product application on external surfaces they should be protected from direct sun rays, wind, rain and/or frost during 24 hours. Application and reaction rate of cement based systems can be affected by environmental and soil temperatures and other conditions, including the air humidity. Low temperatures elongate the hydration period, and result in increase of the product effective life. High temperatures reduce the hydration period, and result in decrease of the above mentioned period. To provide full hardening of the mixture the ambient temperature should not drop below the specified minimum value. After use all hand tools and devices should be cleaned with water.

The required amount of the mixture consumed to obtain 1mm thick layer shall be 1.2 kg/m2.

The product can be stored during 12 months packed in original sacks in dry and cold conditions. For the short storage period the sacks can be placed one upon the other in three layers. In case of long-term storage the product packages should not be laid one upon another. The product in unpacked sacks should be used within one week provided the required storage conditions are maintained.

• when using the Filkret 300 repair mixture observe regulations of operational and personnel safety, wear appropriate protective clothing, safety gloves, glasses, and respirators;
• taking into consideration that the product can cause allergic reactions and itch, take care to avoid contact of its components with skin or eyes, otherwise immediately rinse them with large amount of water and wash with soap;
• in case you swallow the product, immediately consult a physician;
• do not keep food products in the areas of the solution application;
• keep the product away from children;
• parameters indicated above have been received on the basis of laboratory tests conducted in the ambient conditions of +230C±20C temperature and 50% + 5% humidity. Depending on the actual ambient conditions these parameters are subject to change.

• information indicated in technical specifications is based on scientific and experimental data;
• Matanat А company is responsible for the product quality only;
• with the exception of cases of works executed under the supervision of the company specialists, Мatanat А company shall not be liable for any problems occuring due to improper use of the product by other persons;
• the company reserves the right to make changes in its product in consequence of scientific-and-technical development;
• for technical support and or more information please do not hesitate to contact the Matanat А company!