Based on bitumen/rubber latex emulsion, perfectly bonding, elastic after drying, layer forming, waterproofing product, resistant to damp, with no water vapour transmission feature.

This insulating product can be applied in the following areas:

• indoor and outdoor areas, on vertical and horizontal surfaces in currentwise direction of the water flows;
• roof cladding;
• waterproofing of asbestos-cement, asphalt, lead, zinc, aluminum, concrete and wooden surfaces;
• waterproofing of irregular, wavy surfaces;
• waterproofing of channels;
• waterproofing of underground parts of historical monuments;
• waterproofing of walls in indoor and outdoor areas being in contact with soil;
• waterproofing of flower planting areas.

• Monocomponent;
• Ready for application product;
• Easy application onto surface using brush and/or spray applicator gun;
• Can be applied onto fresh concrete and/or wet surfaces;
• Shows high adhesive force when applied both onto dry and wet surfaces;
• Resistant to chemical substances and salt particles contained in the soil;
• Resistant to freezing and melting;
• Does not contain solvents, environmental friendly.

Preparation of the surface. The surfaces to be treated with the product should be healthy, rigid, clean, dust-free, and should have suitable dimensions. The surface should be totally free of any fat, rust, paraffin, and other substances deteriorating adhesive force, and should not have small splinters. Small metal and wooden particles should be removed from the surface, cavities should be filled with repair plaster, and oval shape should be given to the corners. Where appropriate, the IzoBitex can be applied after application of primer layer onto the surface.

Preparation of the mixture. As the IzoBitex product is monocomponent, its preparation is very simple. Take 1 kg of IzoBitex, add 6 liters of water, and mix during 3-5 minutes using 400-600 RPM mixer till the solution is entirely homogeneous.

Application. Spread the product over the whole surface using brush or paddle roller of corresponding size with equal thickness, prevent formation of shrinkage on horizontal surfaces. Where appropriate the IzoBitex can be used as primer layer after mixing with water in the 1/6 proportion (0.02 liter of IzoBitex + 0.14 liter water, totally 0.16 liter/m²). During application consumption of the product may increase by 50% depending on the surface smoothness. After the primer hardening you can pass to the stage of application.

In case of application below the ground level (foundations or other low places) the product can be applied onto the surfaces covered with concrete just after removal of the mould. Immediately after application of the first layer the surface should be strewed with sand. After hardening the sand particles not adhered to the surface should be swept away. Then the second layer is applied, and the surface is strewed with sand again. Where appropriate, this procedure may be repeated further. In case it is required to cover the IzoBitex surface with any protective layer, the final layer should be strewed with sand before hardening. After the surface hardened the sand particles not adhered to the surface should be swept away, and only then the products based on plaster or gypsum may be applied.

Recommendations. After use all hand tools and devices should be cleaned with warm soapy water. After hardening the IzoBitex can be removed from the surface by mechanical means only.

The product can be stored during 12 months packed in original sacks in dry and cold conditions. For the short storage period the sacks can be placed on wooden racks one upon the other in three layers, and in the time of application the lower layer sacks should be used first. In case of long-term storage the product packages should not be laid one upon another.

• when using the product wear the appropriate protective clothing, safety gloves, glasses, and respirators;
• immediately rinse with water in case of contact with skin or eyes;
• in case you swallow the product, immediately consult a physician;
• keep the product away from food and children;
• parameters indicated above have been received on the basis of laboratory tests conducted in the ambient conditions of +230C±20C temperature and 50% + 5% humidity. Depending on the actual ambient conditions these parameters are subject to change.

• information indicated in technical specifications is based on scientific and experimental data;
• Matanat А company is responsible for the product quality only;
• with the exception of cases of works executed under the supervision of the company specialists, Мatanat  А company shall not be liable for any problems occuring due to improper use of the product by other persons;
• the company reserves the right to make changes in its product in consequence of scientific-and-technical development;
• for technical support and/or more information please do not hesitate to contact the Matanat А company!