Cement and perlite-based plaster that has a light filler that is highly hydraulicly polymerized, rich in admixtures increasing the useability of the product, monocomponent, that is resistant to frost, water and external impacts, that has a high resistance and elasticity, and that does not crackle after getting dry. The product conforms to the requirements of the ГОСТ 28013-98 standard.

This product can be applied in the following areas:

• Plastering of concrete surfaces, walls and ceilings built from lightweight concrete;
• Bricklaying, as well as laying of building stone and other types of stones, and plastering of these buildings;
• mechanical plastering of walls and ceilings built from concrete, precast concrete and gas concrete, using plastering machines or by hand.

• surfaces and walls plastered with Fasmatik plastering and laying mixture do not permeate water or moisture to the reverse side;
• It is possible to do facing and finishing works on the wall onto which a plastering material made of the mixture is applied, either directly, or using a facing plaster (primer plaster is saved);
• walls laid or plastered with Fasmatik plastering and laying mixture are warm in winter, and cool in summer;
• the product allows easy and quick use of large-area surfaces using plastering machines, and facilitates the work of a repairman;

Residues preventing adhesion shoud be cleaned off the surface prior to plastering, and the surface should be strong. In case the surface has cracks or broken parts, they should be filled with Filkret repair mortar. Before treatment the surface should be dampened or primed with Binmader primer to achieve  a better result.

In order to make the surface to be treated with plaster flat it is necessary to place plaster profile in a plane. In order to make the wall corners even and accurate, it is required to place a profile angle in a plane with the plaster profiles. These profiles should be installed 24 hours prior to application of plaster onto the surface in order the mixture can set the profiles.

Preparation of mixture (using hand tool). Gently pour out 25 kg Fasmatik plastering and laying mixture to a container filled with 4,0 - 5.0 liters of clean water, then mix using mixer or any hand tool until it is entirely homogeneous. Mix again after 3-4 minutes.

Application (using hand tool). Apply the plaster onto the prepared surface with the thickness of 8-10 mm using trowel, then straighten it with a special straightedge (aluminium profile). The excessive amount of mixture should be excoriated. After the plaster begins to freeze, the surface should be dampened with water, and flattened with a grater. In case it is required to apply the plaster with the thickness more than 2 cm, then the plaster mixture should be applied in 2 phases. The prepared mixture should be used during 120 minutes.

Preparation of mixture (using plastering machine). Put the required amount of Fasmatik plastering and laying mixture in the hopper of plastering machine, then supply the hopper with a continuous water flow. Insert the ratio of Fasmatik machine plaster to the machine program, then start up the machine and mix them automatically in the homogeneous form.

Application (using plastering machine). The ready plaster is applied onto the surface using air compressor located over the machine with the thickness no less than 8-10 mm. The plaster sprayed onto the surface should be straightened using a special straightedge, and the excessive amount of mixture should be abraded. After the plaster begins to freeze, the surface should be dampened with water, and flattened with a grater.

Recommendations. In case the temperature of the environment where Fasmatic machine plaster mixture is used is less than +50C or more than +300C, required temperature should be provided. The product should not be used in hot (more than +300C), rainy and windy weather conditions. No water or dry mixture should be added to the expired mixture. After use all equipment and tools should be cleaned with water.

12-14 kg Fasmatik machine plaster is applied for 8-10 mm thick, 1m2 surface. 25 kg of the Fasmatik machine plaster is enough to plaster the surface with the area of approximately 2 m2.

The product can be stored during 12 months in unopened sacks in dry conditions,  with maximum 10 sacks laid one on another.

• taking into consideration that the Fasmatik machine plaster is rich in chemical compounds, immediately rinse it with water in case of contact with skin or eyes;
• do not add any substances not indicated in the application procedures;
• parameters indicated above were achieved on the basis of laboratory tests conducted in the ambient conditions of +230C±20C temperature and 50% + 5% humidity. Depending on the ambient conditions these parameters may be changed. 

• Information indicated in the technical specifications is based on scientific and practical knowledge;
• “Matanat А" company is responsible only for the product quality;
• Except for the works carried out under the guidance of the company specialists, “Мatanat  А" company bears no responsibility for any problems that may occur as a result of improper use of the product by other users;
• The company reserves the right to make changes to its product that may occur due to a scientific and technnological development;
• For technical support or more information please do not hesitate to contact “Matanat А" company!