Epoxide resin based ready for application adhesive solution, suitable for bonding different products, such as ceramic, marble, granite, acid-resisting ceramic, glass mosaic, and glass bricks, it is resistant to chemical substances (acids) and bacteria, easily applied, washable with water. Adhesive conforms to the requirements of AZS 039-2000 (TS-11140 - 1993) standard “Adhesives – cement based (hydraulic conjunction), suitable for glazed, ceramic, and floor tiles”. (Component A + Component B).

This ceramic adhesive can be applied in the following areas:

• Food production facilities of all types, meat and fish production industry, butcher shops;
• Pharmaceutical, dye, paper, accumulator, and fertilizer industries;
• Printing houses and laundries;
• Kitchens and canteens of industrial facilities;
• Hospitals conforming to different hygienic requirements;
• Swimming pools and thermal springs;
• Waste waters treatment and removal facilities;
• Trade centers, terminals, and other places with busy pedestrian flows;
• Adhesive bonding of different materials, such as ceramic, marble, granite, acid-resisting ceramic, porcelain ceramic, glass mosaic, and glazed tiles onto indoor and outdoor surfaces such as concrete, plaster, and metal.

• Resistant to chemical substances, acids, alkalis, fats, domestic waste waters, chemical waste waters;
• Shows anti-bacterial properties;
• Does not promote formation of mould, epiphytes, and bacteria;
• High mechanical strength;
• Resistant to freezing and warm weather conditions.
• Can be used in areas contacting with potable water;

Preparation of the surfaces. The concrete and other surfaces where facing tiles to be applied should be firm and free of any contaminations. Metal surfaces should be totally free of rust and dirt.

Preparation of the mixture. At the time of use mix together both components of the EPOKS 100 White solution, and then proceed mixing it within at least 3 minutes by means of 400-600 RPM mixer until it is entirely homogeneous.

Application. Apply the EPOKS 100 White solution like all other cement based ceramic adhesives. After mixing apply the product onto the surface using suitable toothed trowel and comb it. Then stick ceramic tiles to the combed surface.

In the areas of heavily spread primer and exposed to heavy loads apply a thin coat of the solution onto the surface of subject to adhesion using flat side of the trowel, then apply epoxide resin based adhesive onto the surface once again and comb it with trowel. After spreading the solution with the toothed trowel immediately bond ceramic tiles. Do not apply ceramic tiles onto the solution when it started to harden.

Recommendations. The EPOKS 100 White solution should be mixed using proper mixing unit. It should be thoroughly mixed by hands or using trowel. Period of use and hardening of adhesive products containing epoxide resins depends on the environmental temperature. The most effective operating temperature is +100C - +200C. The prepared EPOKS 100 White solution mixture in no case should be diluted with water or fresh solution. After use all hand tools and devices should be cleaned with warm water with addition of powdered detergent.

The product can be stored during 12 months packed in original sacks in dry and cold conditions, providing that freezing to be avoided.

• ventilate the area of application of this material until the treated surface is put into operation;
• when using the product strictly observe regulations of operational and personnel safety, wear the proper safety clothing, safety gloves, glasses, and respirators;
• taking into consideration that the solution can cause allergic reaction and itch, take care to avoid contact of its components with skin or eyes, otherwise immediately rinse them with large amount of water and wash with soap;
• in case you swallow the product, immediately consult a physician;
• do not keep food products in the areas of the solution application;
• keep the product away from children;
• parameters indicated above have been received on the basis of laboratory tests conducted in the ambient conditions of +230C±20C temperature and 50% + 5% humidity. Depending on the ambient conditions these parameters are subject to change.

• information indicated in technical specifications is based on scientific and experimental data;
• Matanat А company is responsible for the product quality only;
• with the exception of cases of works executed under the supervision of the company specialists, Мatanat  А company shall not be liable for any problems occuring due to improper use of the product by other persons;
• the company reserves the right to make changes in its product in consequence of scientific-and-technical development;
• for technical support and/or more information please do not hesitate to contact the Matanat А company!